This year I started a course on Advanced Computer Graphics in Aalto University by Jaakko Lehtinen. The focus was on methods for global illumination (GI). In a nutshell, global illumination means more realistic lighting compared to “traditional”, direct lighting, where light is reflected by all surfaces (including diffuse ones). Therefore the shading includes indirect light, colour bleeding, caustics etc. Think of a room with only one window and no additional light, the wall with the window will be also illuminated, but only by light that was reflected from the floor and other walls.
There are many methods of implementing GI, for instance photon mapping, instant radiosity, path tracing and bidirectional path tracing or the quite involved method of Metropolis light transport (MLT). It was obligatory to implement path tracing, but I implemented bidirectional path tracing in addition. As a bonus, I implemented both of the methods on the graphics card using the OptiX Framework from NVIDIA, but please don’t make the same mistake of using OptiX.
Path tracing means tracing a path from the camera, bouncing off of surfaces in a random direction, and doing so until the ray hits the light. On every bounce the reflectance function is used to calculate the amount of reflected light. For instance a red surface would reflect only red light, a white surface all of it and a black one nothing. Naturally one sample is not enough, several samples are taken per pixel and the average gives the actual colour. This results in an unbiased estimation of the colour at the pixel. The technical term for this is Monte Carlo integration.
There are many ways to speed up the convergence, I implemented the following (some of them reused for the bidirectional path tracer):
- At every bounce one additional ray is shot into the direction of a light. This is especially important if the light source is small and hitting it randomly has a small probability. In order not to add the energy from the light twice, a random hit should be ignored.
- The randomly reflected ray should not be sampled according to an uniform distribution, but to a distribution matching the reflectance function and a geometrical term (importance sampling). This gets even more important with a micro-facet model, which was used to simulate partly reflective surfaces (the same model was used for the normal path tracer and the bidirectional one).
- Numbers from a random number generator tend to cluster, which is not optimal for Monte Carlo. A Low-discrepancy sequence is better, because the area of integration is covered more evenly. The Wikipedia Article about the Halton sequence shows the difference.
Bidirectional path tracing
The idea of this method is quite simple, but the implementation is involved. Normal path tracing sometimes has difficulties to sample the light, especially when there are caustics or the light is a bit hidden as it is in the scene above. The reason in both cases is that it can’t be sampled directly (shooting a ray into the direction of the light) and hitting it randomly is improbable. More generally, normal path tracing has difficulties to sample important paths in certain situations, resulting in a noisy image.
Bidirectional path tracing shoots rays from both directions, from the light and from the camera. This results in two paths consisting of vertices, the light and the eye/camera path. Then each camera vertex is connected to each of the light vertices, forming different paths for transporting light. Eric Veach calls them bidirectional sampling techniques. These techniques have different “fields of expertise”, meaning that certain techniques are only efficient for certain effects. The figure on the right shows a collection of such sampling techniques.
In order to compile them into an image, they are weighted and added up. Computing the weight is a bit complex, but basically it’s computing the probability of generating the specific path divided by the sum of generating any path with vertices at the same positions. This results in switching off the techniques for effects that they can’t sample efficiently and therefore results in an image with less noise. This can be observed in the bottom part of the figure on the top right. The technical term is multiple importance sampling and is also covered in depth in Veach’s thesis.
Sub Surface Scattering
Finally I also implemented sub surface scattering. This book contains an excellent explanation of it (the papers (1, 2) by Jensen et al. aren’t so good in my opinion). I chose the accelerated version of the algorithm. This means that I have an octree containing surface points of cached irradiance. It seemed like this is not so cool as expected, the cache needs a lot of space in memory and the objects are lacking the montecarlo noise, which makes them look a bit odd. Blender’s renderer, Cycles, also doesn’t use the acceleration structure, instead they sample the surface directly. If I ever have to implement SSS another time, I’ll do it the Blender way. But for this project I chose to use a hack: In order to fix the unusual look, I mixed in the normal diffuse reflection. So a SSS surface is now 50% SSS and 50% perfectly diffuse.
Because I implemented so many features, I didn’t have enough time to choose nice scenes.
There is one Pangolin, based on a model made by my sister:
then there is the famous Sponza:
and finally a demo scene for the bidirectional tracer:
I was asked to provide the code. Since the project is based on the OptiX Samples framework and the framework has a proprietary license, I can’t give you the full project. Instead I made a diff to the sample directory provided with OptiX 3.0 (as this was the current version when I started coding).
To make it work you need:
1. download OptiX 3.0
2. apply the patch, under Linux it should be possible with the patch tool, something similar should exist on windows
3. if you want to compile and execute my code, download and compile Assimp and FreeImage (the dll’s and header files are assumed to be in folders next to the project folder)
4. follow the instructions in the readme file.
If you have any questions or problems with compiling, feel free to contact me. Preferable via the answer function, so others can also benefit..